How To Set Priority Internet Connection

On Windows 10, if you have a device with more than ane network adapter (such as Ethernet and Wi-Fi), each interface receives a priority value automatically based on its network metric, which defines the primary connection that your device will apply to send and receive networking traffic.

Although, for the most role, Windows 10 does a pretty good job selecting an optimal connectedness to access the network, sometimes you may demand to configure the gild of the network adapters manually. For example, if you want to employ a Wi-Fi over an Ethernet interface when both adapters are connected to the network.

You could disable those adapters you lot don't use, but it may not be the all-time solution equally yous may need them equally backups. Instead, a more than straightforward solution is to adjust the interface metric to specify in which order your device should use each network adapter, which you can do using Control Console and PowerShell.

In this Windows ten guide, nosotros'll walk yous through the steps to change the network adapter priorities to stay connected using your prefered adapter when using multiple interfaces.

• How to change network adapter priorities using Control Panel
• How to change network adapter priorities using PowerShell

How to change network adapter priorities using Command Panel

If you want to alter the order in which Windows 10 uses network adapters, do the post-obit:

1. Open Settings.
2. Click on Network & Internet.
3. Click on Status.
4. Click the Change Adapter options detail.

5. Correct-click the network adapter you lot want to prioritize, and select Properties.

6. Select the Net Protocol Version 4 (TCP/IPv4) detail.
7. Click the Properties push.

8. In the "General" tab, click the Avant-garde push button.

9. Clear the Automatic metric selection.
10. In the "Interface metric" field assign a priority value for the adapter.Quick Tip: The lower the metric number means higher priority, and a higher number indicates lower priority.

11. Click the OK button.
12. Click the OK push again.
13. Click the Shut button.

Once you've completed the steps, Windows 10 will prioritize the network traffic depending on your configuration.

The merely caveat using the Command Panel feel is that depending on your network setup, you may need to adjust the metric for the Internet Protocol Version vi (TCP/IPv6) too, if that'south the protocol you're using. (Normally, you lot will be using the TCP/IPv4 protocol.)

At any fourth dimension, you can revert the changes using the same instructions, only on step No. 9, make sure to cheque the Automatic metric choice.

How to change network adapter priorities using PowerShell

Alternatively, y'all can change network adapters priorities on a device with multiple interfaces using PowerShell with these steps:

1. Open Kickoff.
2. Search for Windows PowerShell, correct-click the top result a select Run equally administrator.
3. Blazon the post-obit control to identify the current interface metric and interface index number and press Enter:Get-NetIPInterface

4. Type the post-obit control to alter the priority gild of the network adapter and press Enter:Set-NetIPInterface -InterfaceIndex 21 -InterfaceMetric 10In the control, make sure to alter the -InterfaceIndex value to reflect the network adapter you want to prioritize and modify the -InterfaceMetric value to assign a priority. Also, think that a lower metric number ways higher priority, and a higher metric number means lower priority.

5. Blazon the following command to see the new metric applied to the network adapter and printing Enter:Get-NetIPInterface

After completing the steps, Windows x will prioritize the network traffic depending on your configuration when multiple network adapters are continued to the network.

At any fourth dimension, yous tin become back to the previous behavior allowing Windows 10 to decide the network adapter priority using these steps:

1. Open Get-go.
2. Search for Windows PowerShell, right-click the top result a select Run as ambassador.
3. Blazon the following command to identify the current interface metric and interface index number and press Enter:Set-NetIPInterface -InterfaceIndex 21 -AutomaticMetric enabledIn the command, brand sure to change the -InterfaceIndex value with the correct number of the network adapter y'all want to apply an automated metric.

More than Windows 10 resources

For more helpful articles, coverage, and answers to common questions about Windows ten, visit the following resources:

• Windows 10 on Windows Central – All y'all need to know
• Windows x help, tips, and tricks
• Windows x forums on Windows Central

Mauro Huculak is technical writer for WindowsCentral.com. His primary focus is to write comprehensive how-tos to help users go the most out of Windows 10 and its many related technologies. He has an It background with professional person certifications from Microsoft, Cisco, and CompTIA, and he'due south a recognized member of the Microsoft MVP customs.

Source: https://www.windowscentral.com/how-change-priority-order-network-adapters-windows-10

Share this post